Are your Water Heater Repair services available in Exeter?

Yes, Masters Plumbing Service provides round-the-clock Water Heater Repair services directly in Exeter, CA.

How much does emergency service cost in Exeter?

We offer upfront, transparent pricing with no hidden fees for all service calls in Exeter.

🔥 Gas, Electric & Tankless Specialists

Water Heater Repair in Exeter, CA — We Fix It Right or Replace It Right

Name: Masters Plumbing Service
Telephone: +1-855-718-1500
Price range: $$
Rating: 4.9

A water heater failure isn't always obvious. Rust-colored hot water, a popping or rumbling noise from the tank, water pooling around the base, or a T&P valve that keeps lifting — each symptom points to a specific component failure. Our techs in Exeter know what each one means and carry the parts to address it.

📞 Call +1-855-718-1500 — Same-Day Service

Gas & Electric Certified in CA Tankless Specialists Parts Stocked On-Truck Repair or Replace — You Decide

Licensed Water Heater Repair service in Exeter, CA - Masters Plumbing Service

Our Qualifications

What Makes Our Water Heater Repair Service Different in Exeter, CA

Water heater work involves gas lines, electrical systems, and pressure vessels — it isn't a DIY project or a job for a generalist. Our techs specialize in water heater diagnosis and carry certifications specific to gas appliance work in CA.

📋

Accurate Diagnosis First

We test before we quote. For a gas unit that's not heating, we check the thermocouple, pilot assembly, gas valve, and burner orifice before recommending any repair. For an electric unit, we test both heating elements and the thermostat with a multimeter. A wrong diagnosis wastes your money on a repair that doesn't fix the problem.

🔩

Stocked for Same-Visit Repairs

Our service trucks carry thermocouples, pilot assemblies, gas valves, upper and lower heating elements, thermostats, T&P relief valves, anode rods, expansion tanks, and flex connectors in the most common sizes. Most water heater repairs in Exeter, CA complete on the first visit without a parts run.

⚖️

Honest Repair vs. Replace Guidance

We give you the numbers. If repair costs approach 50–60% of a replacement unit's installed price and the tank is 8+ years old, we tell you — along with the reasons a new unit makes more financial sense. If the unit is young and the repair is minor, we say that too.

📜

Code-Compliant Installation

Code compliance isn't just legal protection — it's safety. An improperly installed T&P discharge pipe or an undersized flue creates real risk. We install to code every time, not to the cheapest shortcut.

What We Repair & Replace

Every Water Heater Problem We Fix in Exeter

Our techs are trained on all major residential water heater types and brands. Here's how we approach each category of repair.

Gas Tank

Gas Water Heater Repair

We test the gas supply pressure at the unit, check the thermocouple millivolt output with a meter, inspect the burner assembly for debris, and confirm proper draft on the flue. Each of these takes minutes and tells us exactly what component to replace.

Electric Tank

Electric Water Heater Repair

Electric water heater problems nearly always trace to one of three components: the upper heating element, the lower heating element, or the thermostats controlling each. We test both elements with a multimeter for continuity and resistance, check both thermostats for correct setpoint operation, and inspect the reset button for a thermal cutout that's tripped.

Tankless

Tankless Water Heater Repair & Descaling

Scale buildup in the heat exchanger is the leading cause of reduced performance in tankless units in areas with hard water. We perform a vinegar or citric acid descaling flush through the heat exchanger using flush kit ports — restoring flow rate and heating efficiency.

Safety

T&P Valve Replacement

The temperature and pressure relief valve is a critical safety component on every water heater. It should discharge if tank temperature exceeds 210°F or pressure exceeds 150 PSI. A T&P valve that's dripping constantly, won't reset after testing, or shows visible corrosion needs immediate replacement — it's failing in the closed position, which removes the safety protection it provides.

Longevity

Anode Rod Replacement

The sacrificial anode rod — typically magnesium or aluminum — corrodes preferentially inside the tank, protecting the steel tank lining from rusting. When it's depleted, the tank wall begins corroding instead. Most anode rods last 4–6 years in normal water conditions; hard water or water softener use accelerates depletion.

Replacement

Full Water Heater Replacement

We also convert tank-to-tankless installations where the existing infrastructure supports it, including proper gas line sizing for tankless BTU demand and dedicated electrical circuit installation for electric tankless units.

📞 Call +1-855-718-1500 — Diagnose Today

Our Process

From No Hot Water to Restored Heat in 4 Steps

We don't guess at water heater problems. Each call follows a structured diagnostic process that identifies the specific failed component before any repair recommendation is made.

Describe the Symptoms When You Call

No hot water at all? Rusty water? Pilot won't stay lit? Popping or rumbling from the tank? Each symptom points to a short list of likely causes. Describing what you're seeing helps our tech arrive with the most probable replacement parts already on the truck.

Component-Level Diagnosis On-Site

Our tech tests the specific components implicated by your symptoms — not a general inspection of everything. Gas units get thermocouple output tested, gas valve operation checked, pilot assembly inspected. Electric units get both elements and thermostats tested with a meter.

Repair vs. Replace Quote

No pressure tactics. If repair makes sense, we say repair. If the math favors replacement, we show you why.

Same-Visit Repair or Replacement

Approved repairs happen immediately. If we're replacing the unit, we drain and disconnect the old tank, install the new unit with proper flex connectors and expansion tank where required, verify the flue or venting, and test the unit to confirm recovery temperature.

Customer Reviews

Real Exeter Customers, Real Repairs

★★★★★

I'd been getting intermittent hot water for a couple weeks before it stopped entirely. The tech traced it to a failing gas control valve that was cycling the burner erratically. He had the replacement valve on the truck, swapped it, and tested the unit through a full heat cycle before leaving. Explained the whole process clearly.

— B. Larson, Exeter

★★★★★

{Electric water heater wouldn't recover — we'd get about 10 minutes of hot water and then cold. Masters Plumbing Service's tech identified the lower heating element had failed. He drained the tank, replaced the element and lower thermostat while he was in there, and restored full recovery capacity. Explained the difference between upper and lower element function which I'd never understood before.|Woke up to the floor drain running under our water heater — the T&P valve was dripping continuously. The tech identified it wasn't just dripping from normal thermal expansion but was a valve that had corroded open. Replaced the valve, re-routed the discharge pipe to code, and verified tank pressure was within normal range before leaving.}

— M. Torres, Exeter, CA

★★★★★

Called about a tankless that had lost ignition — error code on the display. Tech checked the flame rod, found it had a cracked ceramic insulator causing an intermittent short. Replaced the igniter assembly, unit fired clean on the first restart. He also checked the venting for any obstructions since venting issues can cause similar ignition faults.

— J. Eriksen, Exeter, CA

Trusted Water Heater Repair service in Exeter, CA - Masters Plumbing Service

Common Questions

What People Ask Before Calling

A pilot that lights but won't stay on almost always indicates a failed thermocouple — it's a $15–$40 part that takes under an hour to replace. This is a repair, not a replacement scenario, unless the unit is over 12 years old and showing other signs of wear. We test the thermocouple output with a millivolt meter to confirm it's the cause before ordering the part.

Visible rust staining on the outside of the tank near the base or around the T&P valve outlet often indicates internal corrosion. Once the tank lining is breached, no repair holds long-term. An honest assessment includes checking for these signs before recommending a repair that won't last.

In some cases, rusty hot water in an older tank signals that internal corrosion is already advanced and the tank is near end of life. We inspect the anode rod condition when we diagnose this complaint and give you an honest read on whether replacement makes sense.

Sediment buildup reduces efficiency and can accelerate tank corrosion. Flushing the tank through the drain valve can remove loose sediment; if scale has hardened on the tank floor, flushing is less effective. We assess whether flushing or replacement is the right response based on tank age, severity of buildup, and overall unit condition.

In most jurisdictions in CA, yes — water heater replacement requires a plumbing permit and inspection, particularly for gas units. We pull the required permit as part of the installation and coordinate the inspection. The cost of permitting is disclosed in your quote.

We don't rush. The last 20 minutes of a water heater job — pressure testing connections, cycling the unit, verifying draft on gas units — are as important as the repair itself.

Water Heater Repair in Exeter, CA — We Fix It Right or Replace It Right